Scope. The following sections set out the dates on which ANSI/ASME codes and supplements as required by Public Safety Article, §12-805, Annotated Code of Maryland, became effective. The applicable adopted safety code will be contingent upon the date the contract to install an elevator unit is signed. Documentation verifying the contract date shall be provided as part of the registration process. The elevator unit shall undergo a final acceptance inspection within 3 years of the contract date or the next subsequent adopted safety code shall be applied. Requirements prescribed at the time of the initial elevator certification remain in effect. Frequency of inspection requirements set forth in ANSI Code shall be performed annually, according to Public Safety Article, §12-812, Annotated Code of Maryland. The American Standard Safety Code for Elevators, Dumbwaiters, Escalators, and Moving Walks, ANSI A17.1—1971 and its supplements, are effective on the dates indicated: ANSI A17.1—1971 is effective March 7, 1973; ANSI A17.1a—1972 is effective May 23, 1974; ANSI A17.1b—1973 is effective January 1, 1975; ANSI A17.1c—1974 is effective January 1, 1975; ANSI A17.1d—1975 is effective October 31, 1975; ANSI A17.1e—1975 is effective October 31, 1975; ANSI A17.1f—1975 is effective October 31, 1975; ANSI A17.1g—1976 is effective November 30, 1976. The American Standard Safety Code for Elevators, Dumbwaiters, Escalators, and Moving Walks, ANSI A17.1—1978 and its supplements, are effective on the dates indicated: ANSI A17.1—1978 is effective September 15, 1978; ANSI A17.1a—1979 is effective June 30, 1979; ANSI A17.1b—1980 is effective August 15, 1980. The ANSI/ASME A17.1 Safety Code for Elevators and Escalators, ANSI/ASME A17.1—1981 and its supplements, are effective on the dates indicated: ANSI/ASME A17.1—1981 is effective April 22, 1982; ANSI/ASME A17.1a—1982 is effective May 30, 1983; ANSI/ASME A17.1b—1983 is effective June 23, 1984. The ANSI/ASME A17.1 Safety Code for Elevators and Escalators, ANSI/ASME A17.1—1984 and its supplements, are effective on the dates indicated: ANSI/ASME A17.1—1984 is effective March 16, 1985; ANSI/ASME A17.1a—1985 is effective October 15, 1985; ANSI/ASME A17.1b—1985 is effective April 15, 1986; ANSI/ASME A17.1c—1986 is effective October 31, 1986; ANSI/ASME A17.1d—1986 is effective May 31, 1987; ANSI/ASME A17.1e—1987 is effective October 30, 1987. The ASME/ANSI A17.1 Safety Code for Elevators and Escalators, ASME/ANSI A17.1—1987 and its supplements, are effective on the dates indicated: ASME/ANSI A17.1—1987 is effective July 16, 1988; ASME/ANSI A17.1a—1988 is effective May 16, 1989; ASME/ANSI A17.1b—1989 is effective May 31, 1990. ASME A17.1-1990 Safety Code for Elevators and Escalators and Supplements. The ASME A17.1-1990 Safety Code for Elevators and Escalators, excluding Parts V, XXI, and XXIII, is incorporated by reference and is effective October 14, 1991, with the following changes: On page 87, delete the text under Rule 211.3b Smoke Detectors, and insert in its place the following: On page 163, delete the text under Rule 1000.1 Persons Authorized to Make Inspections and Tests, and insert in its place the following: On page 163, delete the text under Rule 1000.1b(1) and (2) Periodic Inspection and Tests, and insert in its place the following: On page 164, delete the text under Rule 1001.1 Inspection and Test Periods, and insert in its place the following: On page 169, delete the text under Rule 1004.1 Inspection and Test Periods, and insert in its place the following: On page 171, delete the text under Rule 1007.1 Inspections and Test Periods, and insert in its place the following: On page 264, delete the text under Rule 2000.10b(2) Attendant Operation, and insert in its place the following: On page 264, delete the text under Rule 2001.1b Clearances, and insert in its place the following: On pages 266 and 267, delete the text under Rule 2001.6c(1) Platform Guarding, and insert in its place the following: On page 268, delete the text under Rule 2001.10b(2) Attendant Operation, and insert in its place the following: On page 268, delete the text under Rule 2001.10b(4) Attendant Operation, and insert in its place the following: On page 270, delete the text under Rule 2002.6d Footrest Clearance, and insert in its place the following: On pages 289—293, delete the text under Part XXIII, Rooftop Elevators, and insert in its place the following: ASME A17.1a—1991, the Addenda to ASME A17.1—1990 Safety Code for Elevators and Escalators, is incorporated by reference and is effective August 29, 1992. ASME A17.1b—1992, the Addenda to ASME A17.1—1990 Safety Code for Elevators and Escalators. ASME A17.1b—1992 is incorporated by reference and is effective July 5, 1993. The Errata to ASME A17.1b—1992 is incorporated by reference and is effective October 11, 1993. ASME A17.1—1993—Safety Code for Elevators and Escalators and Supplements. The ASME A17.1—1993 Safety Code for Elevators and Escalators, excluding Parts V, XXI, and XXIII, is incorporated by reference and is effective July 18, 1994, with the following changes: On page 27, delete the text under Rule 106.1b(3) Design and Construction of Pits and insert in its place the following: On page 87, delete the text under Rule 211.3b Smoke Detectors, and insert in its place the following: On page 148, delete the text under Rule 802.3f Skirt Panels and insert in its place the following: On page 165, delete the text under Rule 1000.1 Persons Authorized to Make Inspections and Tests, and insert in its place the following: On page 165, delete the text under Rule 1000.1b(1) and (2) Periodic Inspection and Tests, and insert in its place the following: On page 166, delete the text under Rule 1001.1 Inspection and Test Periods, and insert in its place the following: On page 172, delete the text under Rule 1004.1 Inspection and Test Periods, and insert in its place the following: On page 174, delete the text under Rule 1007.1 Inspections and Test Periods, and insert in its place the following: On page 177, delete the text under Rule 1010.10 Wheelchair Lifts, and insert in its place the following: On page 208, delete the text under §1217 Rooftop Elevators, and insert in its place the following: On page 270, delete the text under Rule 2000.10b(2) Attendant Operation, and insert in its place the following: On page 271, delete the text under Rule 2001.1b Clearances, and insert in its place the following: On pages 272 and 273, delete the text under Rule 2001.6c(1) Platform Guarding, and insert in its place the following: On page 274, delete the text under Rule 2001.10b(2) Attendant Operation, and insert in its place the following: On page 274, delete the text under Rule 2001.10b(4) Attendant Operation, and insert in its place the following: On page 276, delete the text under Rule 2002.6d Footrest Clearance, and insert in its place the following: On pages 295—299, delete the text under Part XXIII, Rooftop Elevators, and insert in its place the following: ASME A17.1a-1994 Addenda to ASME A17.1-1993 Safety Code for Elevators and Escalators, excluding Part V, is incorporated by reference and is effective August 24, 1995. The ASME A17.1b-1995 Addenda to ASME A17.1-1993 Safety Code for Elevators and Escalators, excluding Parts V and XXI, is incorporated by reference and is effective March 24, 1997, with the following changes: On page 87, insert the following under Rule 211.3b: On page 166, delete the text under Rule 1001.1 Inspection and Test Periods, and insert in its place the following: On page 174.1, delete the text under Rule 1007.1 Inspections and Test Periods, and insert in its place the following: On page 324.5, delete the text under Rule 2501.12(a). ASME A17.1-1996—Safety Code for Elevators and Escalators and Supplements. The ASME A17.1-1996 Safety Code for Elevators and Escalators, excluding Parts V, XXI, and XXIII, is incorporated by reference and is effective April 6, 1998, with the following changes: On page 31, delete the text under Rule 106.1b(3) Design and Construction of Pits, and insert in its place the following: On page 90, under Rule 210.14 Inspection Operation With Hoistway-Door Electric Contact or Car-Door Electric Contact Open, before the NOTE, insert the following paragraph: On page 92, insert the following under Rule 211.3b Smoke Detectors: On page 158, delete the text under Rule 802.3f Skirt Panels, and insert in its place the following: On page 177, delete the text under Rule 1000.1 Persons Authorized to Make Inspections and Tests, and insert in its place the following: On page 177, delete the text under Rule 1000.1b(1) and (2) Periodic Inspection and Tests, and insert in its place the following: On page 178, delete the text under Rule 1001.1 Inspection and Test Periods, and insert in its place the following: On page 184, delete the text under Rule 1004.1 Inspection and Test Periods, and insert in its place the following: On page 187, delete the text under Rule 1007.1 Inspections and Test Periods, and insert in its place the following: On page 191, delete the text under Rule 1010.10 Wheelchair Lifts, and insert in its place the following: On page 223, delete the text under §1217 Rooftop Elevators, and insert in its place the following: On page 284, delete the text under Rule 2000.10b(2) Attendant Operation, and insert in its place the following: On page 285, delete the text under Rule 2001.1b Clearances, and insert in its place the following: On page 287, delete the text under Rule 2001.6c(1) Platform Guarding, and insert in its place the following: On page 289, delete the text under Rule 2001.10b(2) Attendant Operation, and insert in its place the following: On page 289, delete the text under Rule 2001.10b(4) Attendant Operation, and insert in its place the following: On page 291, delete the text under Rule 2002.6d Footrest Clearance, and insert in its place the following: On pages 309 through 313, delete the text under Part XXIII, Rooftop Elevators, and insert in its place the following: On page 341, delete the text under Rule 2501.12(a). ASME A17.1a-1997 Addenda to ASME A17.1-1996 Safety Code for Elevators and Escalators, excluding Part V, is incorporated by reference and is effective December 28, 1998. ASME A17.1b-1998 Addenda to ASME A17.1-1996 Safety Code for Elevators and Escalators is incorporated by reference and is effective August 23, 1999. ASME A17.1c-1999 Addenda to ASME A17.1-1996 Safety Code for Elevators and Escalators is incorporated by reference and is effective April 1, 2002. ASME A17.1d-2000 Addenda to ASME A17.1-1996 Safety Code for Elevators and Escalators is incorporated by reference and is effective April 1, 2002. ASME A17.1-2000 Safety Code for Elevators and Escalators. The ASME A17.1-2000 Safety Code for Elevators and Escalators, excluding Sections 5.3, 5.4, 5.6, and 5.8, is incorporated by reference with the following change: On page 374, delete the text under Rule 8.11.1.3 Periodic Inspection and Test Frequency, and insert in its place the following: Periodic inspections and tests shall be made at intervals not longer than 1 year. ASME A17.1a-2002 Addenda to ASME A17.1-2000 Safety Code for Elevators and Escalators is incorporated by reference. ASME A17.1b-2003 Addenda to ASME A17.1-2000 Safety Code for Elevators and Escalators is incorporated by reference. ASME A17.1-2004 Safety Code for Elevators and Escalators. The ASME A17.1-2004 Safety Code for Elevators and Escalators, excluding Sections 5.3, 5.4, 5.6, 5.8, and 5.9, is incorporated by reference. ASME A17.1a-2005 Addenda to ASME A17.1-2004 Safety Code for Elevators and Escalators, excluding Sections 5.3, 5.4, 5.6, 5.8, and 5.9, is incorporated by reference. ASME A17.1S-2005 Supplement to ASME A17.1-2004 Safety Code for Elevators and Escalators is incorporated by reference. The ASME A17.1-2007/CSA B44-07 Safety Code for Elevators and Escalators, excluding Sections 5.6, 5.8, and 5.9, is incorporated by reference. ASME A17.1a-2008/CSA B44a-08 Addenda to ASME A17.1-2007/CSA B44-07 Safety Code for Elevators and Escalators is incorporated by reference. ASME A17.1b-2009/CSA B44b-09 Addenda to ASME A17.1-2007/CSA B44-07 Safety Code for Elevators and Escalators is incorporated by reference. ASME A17.1-2010/CSA B44-10 (Revision of ASME A17.1-2007 and CSA B44-07) Safety Code for Elevators and Escalators, excluding Sections 5.6, 5.8, and 5.9, is incorporated by reference. Repealed. Repealed. ASME A17.1-2013/CSA B44-13 (Revision of ASME A17.1-2010/CSA B44-10) Safety Code for Elevators and Escalators is incorporated by reference. ASME A17.1-2016/CSA B44-16 (Revision of ASME A17.1-2013 and CSA B44-13) Safety Code for Elevators and Escalators is incorporated by reference. ASME A17.8-2016/CSA B44.8-16 Standard for wind turbine tower elevators is incorporated by reference. Article 620 Elevators, Dumbwaiters, Escalators, Moving Walks, Platform Lifts, and Stairway Chairlifts of the National Electric Code (NFPA 70), which is incorporated by reference in COMAR 09.12.50.02-1B(3). ASME A17.1-2019/CSA B44-19 (Revision of ASME A17.1-2016 and CSA B44-16) Safety Code for Elevators and Escalators is incorporated by reference. ASME A17.1-2022/CSA B44:22 (Revision of ASME A17.1-2019/CSA B44:19) Safety Code for Elevators and Escalators is incorporated by reference with the following changes: On page 23, after requirement number 2.2.4.2.2: Insert an “(a)” at the beginning of the existing paragraph; and Add new section “(b) For alterations where obstructions are encountered, the width shall be permitted to be decreased to less than 400 mm (16 in.). The reduced width shall be as wide as the available space permits, but not less than 304.8 mm (12 in.)”. On page 24, add to the beginning of requirement 2.2.5.1, “Where access is necessary to service or access elevator equipment,”; On page 232, delete Section 5.8, “Marine Elevators”; On page 233, delete Section 5.9, “Mine Elevators”; On page 241, under requirement 5.10.1.21.3, replace “Article 305 of NFPA 70” with “Article 590 of NFPA 70”; On page 374, delete requirement 8.6.4.24; On page 439, under requirement 8.11.1.4, add at the end of subsection (b)(1) “by bolting, welding, or dry walling to prevent access to the hoistway. The lowest landing may be sealed from outside the hoistway”; and On page 439, under requirement 8.11.1.4, add at the end of section (b)(2) “by bolting, welding, or dry walling to prevent access to the hoistway. The lowest landing may be sealed from outside the hoistway”. ASME A17.8-2021/CSA B44.8:21 Standard for Wind Turbine Tower Elevators is incorporated by reference. In this chapter, the following terms have the meanings indicated. Terms Defined. “First aid” has the meaning stated in 29 CFR §1904.7(b)(5)(ii). “Incident” means an event that results in significant property damage or a major operational malfunction that is not consistent with manufacturer specifications. “Incident report” means a completed Division of Labor and Industry incident record form. “Inclined platform lift” means a hoisting and lowering mechanism equipped with a platform and seat that: Moves in guides in a diagonal plane from one level to another with limited travel, operating speed, and platform area; and Is intended for transportation of mobility-impaired persons. “Inspection report” means a completed Division of Labor and Industry inspection report form. “Passenger elevator” means an elevator used primarily to carry persons other than the operator and persons necessary for loading and unloading. “Qualified” means a person who, by possession of a recognized degree in an applicable field or certificate of professional standing, or who, by extensive knowledge, training, and experience, has successfully demonstrated the ability to solve problems relating to elevator safety. “Safety Code” has the meaning stated in Public Safety Article, §12-801, Annotated Code of Maryland. “Serious injury” means an injury that requires medical treatment by a physician other than one-time first aid, which other treatment does not include diagnostic procedures such as x-ray after the one time treatment, even if provided by a physician. “Serious injury record” means a completed Division of Labor and Industry serious injury record form. “Test report” means a completed Division of Labor and Industry test report form. “Third-Party Qualified Elevator Inspector Report and Checklist” means a completed Division of Labor and Industry Third-Party Qualified Elevator Inspector Report and Checklist form. “Vertical platform lift” means a hoisting and lowering mechanism equipped with a partially enclosed platform that: Moves in guides in a substantially vertical direction with limited travel, operating speed, and platform area; and Is intended for transportation of mobility-impaired persons. “Witness”, as it appears in the Safety Code, means to observe or to verify that testing has been performed by a qualified individual in accordance with the Safety Code. Scope. The following sections set out the dates on which ANSI/ASME codes and supplements for platform lifts and stairway chairlifts, as required by Public Safety Article, §12-805, Annotated Code of Maryland, became effective. Requirements prescribed at the time of the initial platform lift and stairway chairlift certification remain in effect. ASME A18.1-1999 Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference and is effective April 1, 2002. ASME A18.1a-2001 Addenda to ASME A18.1-1999 Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference, as amended, and is effective March 4, 2013. ASME A18.1b-2001 Addenda to ASME A18.1-1999 Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference, as amended, and is effective March 4, 2013. ASME A18.1-2003 (Revision of ASME A18.1-1999) Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference, as amended, and is effective March 4, 2013. ASME A18.1-2005 (Revision of ASME A18.1-2003) Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference, as amended, and is effective March 4, 2013. ASME A18.1-2008 (Revision of ASME A18.1-2005) Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference, as amended, and is effective March 4, 2013. ASME A18.1-2011 (Revision of ASME A18.1-2008) Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference. ASME A18.1-2014 (Revision of ASME A18.1-2011) Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference. ASME A18.1-2017 (Revision of ASME A18.1-2014) Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference. ASME A18.1-2020 (Revision of ASME A18.1-2017) Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference. ASME A18.1-2023 (Revision of ASME A18.1-2020) Safety Standard for Platform Lifts and Stairway Chairlifts is incorporated by reference. In addition to the requirements of Part XX, Inclined Stairway Chairlifts and Inclined and Vertical Wheelchair Lifts, of the A17.1-Safety Code for Elevators, and the requirements of ASME A18.1-1999 Safety Standard for Platform Lifts and Stairway Chairlifts, and all subsequent amendments, §§CF of this regulation apply. General Requirements. Vertical and inclined wheelchair lifts and inclined stairway chairlifts may be used only by physically handicapped individuals, and may not be modified from their intended use. A sign, indicating that the lift is for use by the physically handicapped only, shall be posted at the top and bottom landings of the lift runway. Disconnecting Device. A main line disconnecting device lockable only in the “OFF” position shall be provided. The disconnecting device shall be located within view of the lift motor. Vertical Wheelchair Lift. Adequate car illumination shall be provided during lift operation. An attendant-operated lift shall be operated by a key-activated continuous-pressure switch. Inclined Wheelchair Lift. The edge of the lift's foot rest, facing the upper landing, may not extend more than 12 inches above a step or landing as measured vertically. Self-Closing Door. The platform shall be equipped with a self-closing door on the sides of access to the upper and lower landings. The self-closing door shall be operable within 2 inches of the upper and lower landings. A lift shall be provided with a permanently attached folding seat and seatbelt to accommodate a person not in a wheelchair. Attendant Operation. An attendant-operated lift shall be operated by a key-activated continuous-pressure switch. When the equipment operates on a straight flight of stairs and the platform is within sight during its entire travel, the attendant shall operate the unit from the bottom of the stairs. Inclined Stairway Chairlift. The edge of the lift's foot rest, facing the upper landing, may not extend more than 12 inches above a step or landing as measured vertically. At least 60 days before the planned completion of an elevator, dumbwaiter, escalator, or moving walk, an owner or lessee shall provide the Commissioner with written notice of the planned completion, which shall contain the following information: Contractor name, contact person, address, telephone number, and fax number; Site name, address, and telephone number; Type of elevator, dumbwaiter, escalator, or moving walk; Date of planned completion; Name of manufacturer; and Tentative date of use. Waiver of 60-Day Notice Requirement. If emergency or unusual circumstances are established by the owner or lessee, the Commissioner shall waive the 60-day notice requirement of §A of this regulation. To obtain a waiver, the owner or lessee shall file a written waiver request with the Commissioner: As soon as the emergency or unusual circumstances arise; and Containing a detailed explanation of the emergency or unusual circumstances. If the Commissioner grants a waiver under this section, the Commissioner shall also advise the owner or lessee of when the Notice is due. A final acceptance inspection by the Commissioner is required before the Commissioner may issue a certificate of registration and inspection on all new or modified elevator units. A contractor shall request a final acceptance inspection at least 30 days before the date the contractor requests for the final acceptance inspection to be conducted. A contractor may cancel a scheduled inspection under this regulation by written notice to the Commissioner at least 24 hours before the scheduled inspection. Qualifications. A third-party qualified elevator inspector shall have a valid qualified elevator inspector certification issued by an organization accredited by the American Society of Mechanical Engineers. A third-party qualified elevator inspector shall be: An independent elevator consultant; Employed by an independent inspection agency; or Employed by the insurer of the elevator unit. A third-party qualified elevator inspector shall be registered with the Commissioner before performing inspections pursuant to Public Safety Article, §12-809(d), Annotated Code of Maryland. A third-party qualified elevator inspector, who meets the qualifications set forth in §A(1) and (3) of this regulation, but does not meet the qualifications set forth in §A(2) of this regulation, is authorized to conduct only pre-final inspections under Public Safety Article, §12-810(c)(2), Annotated Code of Maryland. Insurance Requirements. A third-party qualified elevator inspector authorized to conduct periodic no-load elevator inspections shall provide the Commissioner with a certified copy of an insurance policy covering liability related to the third-party qualified elevator inspector performing inspections on elevator units in Maryland. The insurance policy shall be issued by an insurance company authorized to do business in Maryland. The insurance policy shall be in the amount of at least $500,000 for injury or death for any number of individuals in any single occurrence, and $100,000 for property damage in any single occurrence. The insurance policy shall identify the Commissioner as the certificate holder. A third-party qualified elevator inspector shall notify the Commissioner of any material insurance policy alterations or cancellations within 5 business days of receiving notice of the alteration or cancellation. A third-party qualified elevator inspector who conducts only inspections pursuant to Public Safety Article, §12-810(c), Annotated Code of Maryland, is not required to have insurance under this provision. Registration and Renewal. To register initially, a third-party qualified elevator inspector shall submit to the Commissioner a registration fee of $250 and a completed registration form setting forth the following: The applicant's name and address of record; A description of the applicant's education; A list of the applicant's past and present employers; The dates of the applicant's employment with each employer; The position the applicant held with each employer; Proof of certification required by §A of this regulation; and Proof of insurance required by §B of this regulation. A third-party qualified elevator inspector shall renew the registration on an annual basis and submit to the Commissioner the following: A copy of the current qualified elevator inspector certification; A completed renewal application form; and A renewal fee of $250. Suspension, Revocation, or Cancellation of Registration for Third-Party Qualified Elevator Inspectors. Suspension of Registration. After investigation, the Commissioner may suspend the registration of a third-party qualified elevator inspector for the following reasons: Incompetence of the third-party qualified elevator inspector; Untrustworthiness of the third-party qualified elevator inspector; Willful falsification of any matter or statement contained in the registration or renewal form; or Willful falsification of any matter or statement contained in a report or checklist of an inspection made by the third-party qualified elevator inspector. Within 10 days after suspending the registration of a third-party qualified elevator inspector, the Commissioner shall give written notice of the suspension to the third-party qualified elevator inspector. An individual whose third-party qualified elevator inspector registration has been suspended may apply for reinstatement after 120 days following the date of the suspension. Revocation of Registration. Following a suspension of registration under this section, if the Commissioner has reason to believe that a third-party qualified elevator inspector is no longer qualified to hold a registration, the Commissioner may hold a hearing to consider revocation of the third-party qualified elevator inspector's registration. The Commissioner shall give at least 10 days written notice of the hearing to the third-party qualified elevator inspector. At the hearing, the third-party qualified elevator inspector shall be present and may be represented by counsel. The Commissioner shall hold a hearing in accordance with State Government Article, Title 10, Subtitle 2, Annotated Code of Maryland. If, after the hearing, the Commissioner determines that the third-party qualified elevator inspector is no longer qualified to hold a registration, the Commissioner shall immediately revoke the third-party qualified elevator inspector's registration. Cancellation of Registration. A third-party qualified elevator inspector shall be automatically cancelled if the insurance or QEI certification lapses for any reason. An inspection by the Commissioner as provided for in Public Safety Article, §12-809(a), Annotated Code of Maryland is required before a certification of registration and inspection is issued. Record Keeping. At a readily accessible central location in the building where the elevator unit is located, a contractor, owner, or lessee shall maintain: A legible hard copy of maintenance, repair, test, and inspection records; or An electronic copy of maintenance, repair, test, and inspection records in an electronic format approved by the Commissioner for that location. The records required to be filed with the Commissioner shall be filed pursuant to the following time intervals: Incident reports shall be filed within 5 business days of the contractor, owner, or lessee having knowledge of the incident; and Serious injury records shall be filed within 24 hours of the contractor, owner, or lessee having knowledge of the occurrence. When the Commissioner requires records to be filed electronically, they shall be filed in comma delimited or tab delimited format, except when to do so would pose an undue burden. An owner shall hire a third-party qualified elevator inspector who is registered and authorized to perform periodic annual inspections under Regulation .04-1 of this chapter to conduct inspections under Public Safety Article, §12-809(d), Annotated Code of Maryland. An inspection by a third-party qualified elevator inspector as provided for under Public Safety Article, §12-809(d), Annotated Code of Maryland, is required before a certification of registration and inspection is issued. The Commissioner may not issue a certificate of registration and inspection to an owner until the third-party qualified elevator inspector has filed an inspection report certifying compliance with the Safety Code and regulations adopted by the Commissioner. An owner shall ensure that an elevator unit suspended by wire ropes, belts, chains, or a similar suspension or an elevator with rack and pinion drive has a comprehensive 5-year inspection. Comprehensive 5-Year Inspection. A comprehensive 5-year inspection under §D of this regulation is a periodic annual inspection and a full load test performed on an elevator unit as defined in the Safety Code as a Category 5 Periodic Test. For a comprehensive 5-year inspection: The Commissioner shall establish the 5-year inspection anniversary date for each unit; An owner shall ensure that each unit is tested by persons qualified to perform such testing as provided in the Safety Code; An owner shall coordinate with the Commissioner the date and time of the inspection by filing an inspection request with the Commissioner at least 60 days prior to the inspection; and If an owner provides the Commissioner with less than 60 days notice of the inspection request, the Commissioner shall schedule the inspection at the convenience of the State, subject to the availability of State resources. This regulation does not preclude an owner from having an elevator unit inspected more frequently than required by this regulation. A Level I inspector is a third-party qualified elevator inspector who may perform pre-final inspections and periodic annual inspections if the individual: Possesses and maintains a valid third-party qualified elevator inspector certification; Is employed as an independent consultant or by an independent inspection agency or is employed by the insurer of the elevator unit; and Possesses and maintains insurance as required by Regulation .04-1 of this chapter. A Level II inspector is a third-party qualified elevator inspector who may perform only pre-final inspections if the individual possesses and maintains a valid qualified elevator inspector certification. A third-party qualified elevator inspector is authorized to perform only pre-final inspections on a personnel hoist under the ANSI A10.4 Code if approved by the Commissioner after submission of the following information: Documentation detailing experience, manufacturer's training, and knowledge of personnel hoists, safety codes, maintenance, and testing; and Any additional information requested by the Commissioner. A third-party qualified elevator inspector shall ensure that inspections and tests are performed consistent with the ASME A17.2 Guide for Inspection of Elevators, Escalators, and Moving Walks and the Safety Code. Within 30 days of the completion of the periodic annual inspection, the third-party qualified elevator inspector shall submit to the Commissioner the Third-Party Elevator Inspector Report and Checklist form detailing the inspection findings and certifying whether the elevator unit is in compliance with the Safety Code and regulations adopted by the Commissioner. If, during the course of a periodic annual inspection of an elevator unit, a third-party qualified elevator inspector finds a potential violation of the Safety Code or any regulation adopted by the Commissioner, the third-party qualified elevator inspector shall provide the owner with the opportunity to abate and correct the alleged violation. When an inspection by a third-party qualified elevator inspector discloses that an elevator unit is in an unsafe condition so that its continued operation is likely to expose a passenger on an elevator unit to the threat of serious injury, the third-party qualified elevator inspector shall: Advise the owner to cease operation of the elevator unit; and Notify the Commissioner immediately. Public Safety Article, §§12-805, 12-806, and 12-809, Annotated Code of Maryland Effective date: Regulation .01A adopted effective July 13, 1979 (6:14 Md. R. 1207) Regulation .01B adopted effective February 1, 1980 (7:2 Md. R. 114) Regulation .01C adopted effective August 16, 1982 (9:16 Md. R. 1605) Regulation .01D adopted effective September 1, 1982 (9:16 Md. R. 1605) Regulation .01E adopted effective November 1, 1983 (10:21 Md. R. 1900) Regulation .01F adopted effective December 17, 1984 (11:25 Md. R. 2133) Regulation .01F amended as an emergency provision effective September 26, 1986 (13:21 Md. R. 2311) (Emergency provisions are temporary and not printed in COMAR) Regulation .01G adopted effective January 28, 1985 (12:2 Md. R. 137) Regulation .01H amended as an emergency provision effective September 26, 1986 (13:21 Md. R. 2311) (Emergency provisions are temporary and not printed in COMAR) Chapter revised effective November 2, 1987 (14:22 Md. R. 2339) Regulation .01A amended effective April 28, 2003 (30:8 Md. R. 540); August 4, 2014 (41:15 Md. R. 890) Regulation .01E amended effective January 25, 1988 (15:2 Md. R. 120) Regulation .01F adopted effective December 26, 1988 (15:26 Md. R. 2981) Regulation .01F amended effective October 10, 1989 (16:19 Md. R. 2104); November 12, 1990 (17:22 Md. R. 2655) Regulation .01G adopted effective October 14, 1991 (18:20 Md. R. 2198) Regulation .01G amended effective March 2, 1992 (19:4 Md. R. 473); August 29, 1992 (19:16 Md. R. 1473); July 5, 1993 (20:13 Md. R. 1048); October 11, 1993 (20:20 Md. R. 1569) Regulation .01H adopted effective July 18, 1994 (21:14 Md. R. 1229) Regulation .01H amended effective August 28, 1995 (22:17 Md. R. 1317) Regulation .01H amended as an emergency provision effective April 25, 1996 (23:10 Md. R. 727); emergency status expired October 25, 1996 Regulation .01H amended effective November 18, 1996 (23:23 Md. R. 1556); March 24, 1997 (24:6 Md. R. 484) Regulation .01I adopted effective April 6, 1998 (25:7 Md. R. 526) Regulation .01J adopted effective December 28, 1998 (25:26 Md. R. 1921) Regulation .01K adopted effective October 4, 1999 (26:20 Md. R. 1545) Regulation .01L, M adopted effective April 1, 2002 (29:6 Md. R. 567) Regulation .01N adopted effective April 28, 2003 (30:8 Md. R. 540) Regulation .01O adopted effective September 29, 2003 (30:19 Md. R. 1331) Regulation .01P adopted effective March 14, 2005 (32:5 Md. R. 580) Regulation .01Q, R, S adopted effective April 7, 2008 (35:7 Md. R. 748) Regulation .01T, U adopted as an emergency provision effective August 21, 2009 (36:19 Md. R. 143); adopted permanently effective November 16, 2009 (36:23 Md. R. 1816) Regulation .01T amended effective July 25, 2011 (38:15 Md. R. 899) Regulation .01U—W amended effective December 26, 2011 (38:26 Md. R. 1696) Regulation .01W—Y amended effective July 8, 2013 (40:13 Md. R. 1073) Regulation .01W amended effective July 16, 2018 (45:14 Md. R. 695) Regulation .01X, Y repealed effective July 16, 2018 (45:14 Md. R. 695) Regulation .01Z, AA adopted effective July 16, 2018 (45:14 Md. R. 695) Regulation .01BB, CC adopted effective July 16, 2020 (47:14 Md. R. 675) Regulation .01DD adopted effective October 22, 2022 (49:9 Md. R. 531) Regulation .01EE, FF adopted effective June 17, 2026 (53:8 Md. R. 355) Regulation .01-1 adopted effective January 29, 2007 (34:2 Md. R. 137) Regulation .01-1B amended as an emergency provision effective October 15, 2007 (34:23 Md. R. 2019); amended permanently effective February 25, 2008 (35:4 Md. R. 514) Regulation .01-1B amended as an emergency provision effective August 21, 2009 (36:19 Md. R. 1433); amended permanently effective November 16, 2009 (36:23 Md. R. 1816) Regulation .02 amended effective August 28, 1995 (22:17 Md. R. 1317); April 6, 1998 (25:7 Md. R. 526); April 1, 2002 (29:6 Md. R. 567) Regulation .02A amended effective July 16, 2020 (47:14 Md. R. 675); July 24, 2023 (Md. R. 50:14 592); June 17, 2026 (53:8 Md. R. 355) Regulation .02A, B amended effective March 4, 2013 (40:4 Md. R. 345) Regulations .03—.06 adopted as an emergency provision effective July 5, 2001 (28:15 Md. R. 1394); adopted permanently effective October 1, 2001 (28:19 Md. R. 1684) Regulation .04A amended as an emergency provision effective October 15, 2007 (34:23 Md. R. 2019); amended permanently effective February 25, 2008 (35:4 Md. R. 514) Regulation .04-1 adopted as an emergency provision effective October 15, 2007 (34:23 Md. R. 2019); adopted permanently effective February 25, 2008 (35:4 Md. R. 514) Regulation .04-1A amended as an emergency provision effective August 21, 2009 (36:19 Md. R. 1433); amended permanently effective November 16, 2009 (36:23 Md. R. 1816) Regulation .04-1C amended as an emergency provision effective January 11, 2008 (35:3 Md. R. 285); emergency status expired June 9, 2008 Regulation .05 amended effective January 29, 2007 (34:2 Md. R. 137) Regulation .05 amended as an emergency provision effective October 15, 2007 (34:23 Md. R. 2019); amended permanently effective February 25, 2008 (35:4 Md. R. 514) Regulation .05 amended as an emergency provision effective August 21, 2009 (36:19 Md. R. 1433); amended permanently effective November 16, 2009 (36:23 Md. R. 1816) Regulation .06 amended effective January 29, 2007 (34:2 Md. R. 137) Regulation .06A amended effective June 17, 2026 (53:8 Md. R. 355) Regulation .06B, C amended as an emergency provision effective October 15, 2007 (34:23 Md. R. 2019); amended permanently effective February 25, 2008 (35:4 Md. R. 514) Regulation .07 adopted as an emergency provision effective August 21, 2009 (36:19 Md. R. 1433); adopted permanently effective November 16, 2009 (36:23 Md. R. 1816) Regulation .08 adopted as an emergency provision effective August 21, 2009 (36:19 Md. R. 1433); adopted permanently effective November 16, 2009 (36:23 Md. R. 1816)